Discovering Plumbing Basics is Crucial When Installing a Bathtub
Discovering Plumbing Basics is Crucial When Installing a Bathtub
Blog Article
We've stumbled upon the article pertaining to A Step-by-Step Guide to Installing a Bathtub directly below on the internet and believe it made perfect sense to talk about it with you on this site.
Setting up a tub isn't exactly brain surgery, however it does need solid plumbing, carpentry, and also occasionally, tiling abilities. Changing an old bathtub with a brand-new one is likewise a reasonably hard project. If the old tub is readily easily accessible, the project can move quickly; if you have to open a wall surface to get rid of the old bathtub as well as position the brand-new bath tub, the job is much harder. In either instance, the project is within a home handyman's abilities, although you will certainly need a helper to vacate the old tub and also set in the new one. Make sure you have qualified on your own for the job and are comfortable trying it. As opposed to working with a professional to take over a halfway-completed project, it is far better to consider utilizing one before you start. Possibilities are you might need a specialist plumber to make tube connections.
This short article will certainly aid you install a new bath tub in your washroom if you have actually already purchased a brand-new tub and do not require to alter the plan of your previous water supply pipelines.
Your devices as well as product list need to make up the following:
Getting ready for the Setup
Firstly, the sustaining frame supplied with the bathroom must be fitted (if called for) according to the manufacturer's guidelines. Next, fit the faucets or mixer to the tub. When suitable the tap block, it is necessary to ensure that if the tap includes a plastic washing machine, it is fitted in between the bathroom as well as the faucets. On a plastic bathroom, it is also reasonable to fit a sustaining plate under the faucets device to avoid strain on the tub.
Fit the adaptable tap connectors to the bottom of the two taps making use of 2 nuts and also olives (in some cases provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet via the hole in the bath. Utilize the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bathroom. See to it you make use of every one of the supplied washing machines.
Attach the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Link the bottom of the overflow tube in a similar manner.The bathroom should now prepare to be fitted in its final position.
Removing Old Taps
If you require to change old taps with new ones as a part of your setup, then the first thing you must do is detach the water. After doing so, switch on the faucets to drain pipes any water continuing to be in the system. The procedure of removing the existing faucets can be rather troublesome because of the limited accessibility that is often the case.
Use a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that attaches the supply pipelines to the faucets. Have a fabric prepared for the continuing to be water that will come from the pipelines. When the supply pipelines have been gotten rid of, utilize the same device to loosen the nut that holds the faucets onto the bath/basin. You will need to stop the single taps from turning during this procedure. As soon as the taps have been gotten rid of, the holes in the bath/basin will certainly need to be cleaned up of any old sealing compound.
Before moving on to fit the new taps, compare the pipeline connections on the old taps to the brand-new faucets. If the old faucets are longer than the new taps, after that a shank adapter is required for the new taps to fit.
Setting up the Bath tub
Using the two wood boards under its feet, place the bath tub in the needed placement. The wooden boards are valuable in uniformly spreading out the weight of the tub over the location of the boards as opposed to focusing all the weight onto 4 small points.
The following goal is to make sure that the tub is leveled all round. This can be achieved by examining the spirit level and also adjusting the feet on the tub till the spirit level reads degree.
To set up faucets, fit the bottom of the outermost flexible tap port to the appropriate supply pipeline by making a compression sign up with; after that do the exact same for the various other faucet.
Activate the supply of water and check all joints as well as new pipework for leakages and tighten them if needed. Fill the bathtub as well as additionally check the overflow electrical outlet as well as the typical electrical outlet for leakages.
Finally, take care of the bathroom paneling as explained in the maker's instruction manual. Tiling and also securing around the tub must wait till the tub has been made use of at the very least once as this will certainly resolve it right into its last setting.
Suitable New Touches
If the tails of the brand-new faucets are plastic, then you will certainly require a plastic connector to prevent damage to the thread. One end of the connector fits on the plastic tail of the tap as well as the various other end offers a link to the existent supply pipelines.
If you need to fit a monobloc, after that you will certainly require lowering couplers, which connects the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next, place the tap in the installing hole in the bath/basin guaranteeing that the washing machines are in location in between the faucet and the sink. Secure the tap in position with the manufacturer offered backnut. Once the tap is firmly in place, the supply pipelines can be linked to the tails of the faucets. The taps can either be linked by using corrugated copper piping or with regular tap adapters. The previous kind must be attached to the faucet ends initially, tightening only by hand. The supply pipelines can later on be linked to the various other end. Tighten both ends with a spanner after both ends have been attached.
Tiling Around the Bath tub
In the location where the bath meets the tile, it is necessary to secure the accompanies a silicone rubber caulking. This is necessary as the installation can move sufficient to break a stiff seal, causing the water to pass through the wall between the bath and the tiling, leading to difficulties with dampness as well as feasible leakages to the ceiling below.
You can pick from a range of coloured sealers to blend in your fixtures as well as installations. They are offered in tubes as well as cartridges, and also can sealing gaps up to a width of 3mm (1/8 inch). If you have a bigger void to load, you can fill it with spins of soaked newspaper or soft rope. Keep in mind to constantly load the bath tub with water prior to sealing, to allow for the motion experienced when the tub remains in usage. The sealant can break rather very early if you do not consider this activity before securing.
Conversely, ceramic coving or quadrant tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are additionally easily available on the market. It is advisable to fit the tiles using water-resistant or water-proof sticky as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I'm certainly very eager about How to Install a Bathtub and I really hope you enjoyed reading the new article. Sharing is caring. Helping people is fun. We enjoy reading our article about Installing A Bathtub.
Best choice? Ring us! Report this page